Modify Manual – JDG Polymer80 Licensed PF940V2 Airsoft Frame for UMAREX Glock 17 Gen3 Ver.

Corresponds to the following models:
JDG0017, JDG0018, JDG0019.
” JDG Polymer80 Licensed P80 PF940V2 Airsoft Frame for Model 17 Gen3 ( TM / WE ) “

JDG Polymer80 Licensed PF940V2 Frame for Glock 17 Gen3 ( UMAREX / TM / WE )
FOR AIRSOFT AND SIMULATION USE ONLY.
1. Acquire a flat file or a Dremel tool, and a caliper for the modification to fit UMAREX internal parts into the JDG Polymer80 Frame.
1. ๆบ–ๅ‚™ๅทฅๅ…ท๏ผŒๅฏๅฐ‡้Šผๅˆ€ๆŸ„ๅ…ˆ็จๅพฎๅฝŽๆ›ฒๅ‚™็”จ๏ผŒไพไฝฟ็”จ่€…ๅ€‹ไบบ็‹€ๆณ๏ผŒไบฆๅฏไฝฟ็”จ้›ป็ฃจๆฉŸใ€‚
2. File or grind down the front locking block by 0.25mm to 0.3mm
2. ๅฐ‡ JDG Polymer80 ไธ‹่บซๆกๆŠŠ็š„ๅ‰่žบๅญ”ไปฅ้Šผๅˆ€ๅพ€ไธ‹็ฃจ0.25mm่‡ณ0.3mm
3. File the rear part of the UMAREX locking block by about 0.2mm
3. ๅฐ‡ UMAREX ็š„ๅฐŽ่ปŒๅบงๅพŒ็ซฏๅพ€ไธ‹็ฃจๅนณ็ด„ 0.2mm
4. File away the portion where the hammer assembly sits as shown above by about 0.8mm to 1mm to fit the UMAREX hammer assembly.
4. ไฟฎๆ”น JDG Polymer80 ไธ‹่บซๆกๆŠŠๅพŒๆ–น็š„ๆ“Š้Žšๅบงไฝ็ฝฎ๏ผŒไธฆๅพ€ไธ‹็ฃจ 0.8mm-1mm๏ผŒไปฅไพฟๆ“Š้Žšๅฏๆญฃๅธธๆ‰ฃ่‘—็‚บไธปใ€‚
5. We recommend adding an o-ring (2.5mm outer diameter, 1.5mm inner diameter) on the hammer assembly screw to make the screw fit tightly against the frame.
5. ๅฐ‡ๆ‰€ๆœ‰้›ถไปถไพๅบ่ฃๅ›ž๏ผŒๅ‰่žบ็ตฒๅปบ่ญฐๅฏๅŠ 1ๅ€‹Oๅž‹ๅœˆ๏ผˆ็ทšๅพ‘1.5mm๏ผŒๅ…งๅพ‘2.5 mm๏ผ‰๏ผŒไฝฟๅฐŽ่ปŒ่ˆ‡ไธ‹่บซ็ตๅˆๆ›ด็ทŠๅฏ†ใ€‚
Finished

DISCLAIMER: THESE ARE AIRSOFT TOYS ONLY, DOES NOT AND CAN NOT FIT REAL FIREARMS.

, , ,

Janus Division Group | JDG